remove not needed sources
This commit is contained in:
Oliver Lehmann
parent
946ac0cdb5
commit
89eaf490b5
|
|
@ -1,181 +0,0 @@
|
|||
!******************************************************************************
|
||||
*******************************************************************************
|
||||
|
||||
W E G A - Quelle (C) ZFT/KEAW Abt. Basissoftware - 1986
|
||||
|
||||
PROM Modul: DISK.S fuer P8000-WDC
|
||||
|
||||
Bearbeiter: P. Hoge
|
||||
Datum: $D$
|
||||
Version: $R$
|
||||
|
||||
*******************************************************************************
|
||||
******************************************************************************!
|
||||
|
||||
disk module
|
||||
|
||||
|
||||
$SECTION PROM
|
||||
$nonsegmented
|
||||
|
||||
constant
|
||||
|
||||
!Port Adressen!
|
||||
|
||||
PIOAD := %FFA1 !Daten lesen / schreiben!
|
||||
PIOBD := %FFA3 !Steuerport !
|
||||
PIOAC := %FFA5
|
||||
PIOBC := %FFA7
|
||||
|
||||
!PIO Programmierung!
|
||||
|
||||
OUTPUT := %0F
|
||||
INPUT := %4F
|
||||
BITMODE := %CF
|
||||
INTVEC := %18
|
||||
|
||||
!Anschlussbelegung des Controlers am U880 PIO
|
||||
|
||||
PORT A: 8 bit bidirektionale Daten (D0 bis D7)
|
||||
PORT B:
|
||||
bit 0: /ST0 (Interrupt Request), Eingang
|
||||
bit 1: /ST1 (Anforderung der Daten), Eingang
|
||||
bit 2: /ST2 (Error), Eingang
|
||||
bit 3: frei, Ausgang
|
||||
bit 4: frei, Ausgang
|
||||
bit 5: RESET (WDC-Reset), Ausgang
|
||||
bit 6: TE und Richtung Datentreiber 0=write 1=read Ausgang
|
||||
bit 7: TR (Transfer Request), Eingang
|
||||
!
|
||||
!WDC Steuerport!
|
||||
|
||||
RDATA := %4000 !Daten lesen!
|
||||
WDATA := %00 !Daten schreiben!
|
||||
RESET := %80 !Reset an Controler ausgeben!
|
||||
|
||||
!WDC-Kommandos!
|
||||
|
||||
COMMAND := %20 !Read/Write ab Blocknummer!
|
||||
READ := %21 !Read ab Blocknummer!
|
||||
WRITE := %22 !Write ab Blocknummer!
|
||||
|
||||
|
||||
global
|
||||
|
||||
!------------------------------------------------------------------!
|
||||
! Eingabeparameter: r7 .... Request-Code (1=Read, 2=Write) !
|
||||
! r6 .... Drive-Nr. !
|
||||
! rr4 .... Blocknummer !
|
||||
! rr8 .... Pufferadresse !
|
||||
! r10 .... Laenge (<=%200) !
|
||||
! Der Return-Code wird in r2 zurueckgegeben !
|
||||
!------------------------------------------------------------------!
|
||||
|
||||
DISK procedure
|
||||
entry
|
||||
callr _disk_in !Hardware init!
|
||||
|
||||
ldl rr2, rr4
|
||||
ld r4, #PIOAD
|
||||
ld r5, #PIOBD
|
||||
ld r0, #WDATA+OUTPUT
|
||||
outb @r5, rh0 !Datentreiber auf Ausgabe!
|
||||
outb PIOAC, rl0 !Daten-PIO auf Ausgabe!
|
||||
|
||||
wready: inb rl0, @r5
|
||||
bitb rl0, #0
|
||||
jr nz, wready !Warten bis WDC bereit!
|
||||
|
||||
!WDC-Kommando ausgeben!
|
||||
|
||||
orb rl7, #COMMAND
|
||||
outb @r4, rl7 !Kommando ausgeben!
|
||||
outb @r4, rl6 !Laufwerknummer!
|
||||
outb @r4, rl3 !Blocknummer low!
|
||||
outb @r4, rh3
|
||||
outb @r4, rl2
|
||||
outb @r4, rh2 !Blocknummer high!
|
||||
ld r3, r10 !Laenge!
|
||||
outb @r4, rl3
|
||||
outb @r4, rh3
|
||||
outb @r4, rh6 !Pruefsumme, nicht benutzt!
|
||||
|
||||
wwait0: inb rl0, @r5 !Warten bis WDC Status 0!
|
||||
bitb rl0, #0
|
||||
jr z,wwait0
|
||||
|
||||
ld r6, #%C000 !FCW!
|
||||
cpb rl7, #WRITE
|
||||
jr nz, rwwait
|
||||
|
||||
wwait1: inb rl0, @r5 !Write!
|
||||
bitb rl0, #1 !Warten, bis WDC bereit fuer Daten!
|
||||
jr nz, wwait1
|
||||
ldctl r1, FCW
|
||||
ldctl FCW, r6
|
||||
!$segmented!
|
||||
otirb @r4, @r8, r3 !otirb @r4, @rr8, r3!
|
||||
ldctl FCW, r1
|
||||
!nonsegmented!
|
||||
|
||||
wwait2: inb rl0, @r5 !Warten bis WDC Status 0!
|
||||
bitb rl0, #1
|
||||
jr z,wwait2
|
||||
|
||||
rwwait: inb rl1, @r5 !Status einlesen!
|
||||
bitb rl1, #0
|
||||
jr nz, rwwait !auf Beendigung des Kommandos warten!
|
||||
inb rl1, @r5
|
||||
andb rl1, #%07 !Maske!
|
||||
ldk r2, #0 !Returncode kein Fehler!
|
||||
cpb rl1, #%06 !Status 1 = fertig, kein Fehler!
|
||||
ret z
|
||||
|
||||
ld r0, #RDATA+INPUT
|
||||
outb PIOAC, rl0 !Daten-PIO auf Eingabe!
|
||||
outb @r5, rh0 !Treiber auf Eingabe!
|
||||
inb rl0, @r4 !Scheineingabe!
|
||||
cpb rl1, #%04 !Status 3 Daten einlesen ?!
|
||||
jr nz, error !nein, Fehler!
|
||||
|
||||
ldctl r1, FCW
|
||||
ldctl FCW, r6
|
||||
!$segmented!
|
||||
inirb @r8, @r4, r3 !inirb rr8, @r4, r3!
|
||||
ldctl FCW, r1
|
||||
!$nonsegmented!
|
||||
ret
|
||||
|
||||
error: inb rl2, @r4 !Fehlercode einlesen!
|
||||
ret
|
||||
end DISK
|
||||
|
||||
|
||||
!Initialisierung der Ports und des Controlers!
|
||||
|
||||
internal
|
||||
|
||||
init array [* byte] := [
|
||||
PIOBC, INTVEC !Int Vektor holt PIO Port aus Reset!
|
||||
PIOBD, WDATA !Reset wegnehmen, Richtung auf Write!
|
||||
PIOBC, BITMODE !Port B auf Bitmode programmieren!
|
||||
PIOBC, %87 !bit 7,2,1,0 auf Eingabe!
|
||||
]
|
||||
|
||||
_disk_in procedure
|
||||
entry
|
||||
ld r2, #PIOBD
|
||||
inb rl1, @r2 !PIOBD schon initialisiert ?!
|
||||
bitb rl1, #5
|
||||
ret z !ja!
|
||||
|
||||
lda r1, init
|
||||
ldk r0, #(sizeof init)/2 !Anzahl der Ausgaben!
|
||||
iloop: ldb rl2, @r1 !low Portadresse!
|
||||
inc r1, #1
|
||||
outib @r2, @r1, r0
|
||||
jr nov, iloop
|
||||
ret
|
||||
end _disk_in
|
||||
|
||||
end disk
|
||||
|
|
@ -1,169 +0,0 @@
|
|||
!******************************************************************************
|
||||
*******************************************************************************
|
||||
|
||||
W E G A - Quelle (C) ZFT/KEAW Abt. Basissoftware - 1985
|
||||
|
||||
Standalone: sa.fdisk.s fuer P8000-WDC
|
||||
|
||||
|
||||
Bearbeiter: P. Hoge
|
||||
Datum: 04/01/87 11:20:53
|
||||
Version: 1.1
|
||||
|
||||
*******************************************************************************
|
||||
******************************************************************************!
|
||||
|
||||
|
||||
|
||||
fdisk module
|
||||
|
||||
$nonsegmented
|
||||
|
||||
|
||||
constant
|
||||
|
||||
!Port Adressen!
|
||||
|
||||
PIOAD := %FFA1 !Daten lesen / schreiben!
|
||||
PIOBD := %FFA3 !Steuerport !
|
||||
PIOAC := %FFA5
|
||||
PIOBC := %FFA7
|
||||
|
||||
!PIO Programmierung!
|
||||
|
||||
OUTPUT := %0F
|
||||
INPUT := %4F
|
||||
BITMODE := %CF
|
||||
INTVEC := %18
|
||||
|
||||
!Anschlussbelegung des Controlers am U880 PIO
|
||||
|
||||
PORT A: 8 bit bidirektionale Daten (D0 bis D7)
|
||||
PORT B:
|
||||
bit 0: /ST0 (Interrupt Request), Eingang
|
||||
bit 1: /ST1 (Anforderung der Daten), Eingang
|
||||
bit 2: /ST2 (Error), Eingang
|
||||
bit 3: frei, Ausgang
|
||||
bit 4: frei, Ausgang
|
||||
bit 5: RESET (WDC-Reset), Ausgang
|
||||
bit 6: TE und Richtung Datentreiber 0=write 1=read Ausgang
|
||||
bit 7: TR (Transfer Request), Eingang
|
||||
!
|
||||
!WDC Steuerport!
|
||||
|
||||
RDATA := %4000 !Daten lesen!
|
||||
WDATA := %00 !Daten schreiben!
|
||||
RESET := %80 !Reset an Controler ausgeben!
|
||||
|
||||
!WDC-Kommandos!
|
||||
|
||||
READ := %01 !Read mit Sektoradresse!
|
||||
FORMAT := %04 !Formatieren einer Spur!
|
||||
|
||||
internal
|
||||
|
||||
rbuffer array [512 byte]
|
||||
|
||||
|
||||
!------------------------------------------------------------------!
|
||||
! Eingabeparameter: r7 .... Request-Code (1=Read, 3=Format) !
|
||||
! r6 .... Drivenummer !
|
||||
! r5 .... Kopf !
|
||||
! r4 .... (Anzahl der Sektoren) !
|
||||
! r3 .... Sektornummer (fuer Read) !
|
||||
! r2 .... Zylindernummer !
|
||||
! Returncode in r2 !
|
||||
!------------------------------------------------------------------!
|
||||
|
||||
global
|
||||
|
||||
_fdisk procedure
|
||||
entry
|
||||
push @r15, r5
|
||||
push @r15, r2
|
||||
calr _disk_in !Hardware initialisieren!
|
||||
|
||||
ld r4, #PIOAD
|
||||
ld r5, #PIOBD
|
||||
ld r0, #WDATA+OUTPUT
|
||||
outb @r5, rh0 !Datentreiber auf Ausgabe!
|
||||
outb PIOAC, rl0 !Daten-PIO auf Ausgabe!
|
||||
|
||||
wready: inb rl0, @r5
|
||||
bitb rl0, #0
|
||||
jr nz, wready !Warten bis WDC bereit!
|
||||
|
||||
!WDC-Kommando ausgeben!
|
||||
|
||||
cpb rl7, #3 !Format ?!
|
||||
jr nz, read !Requestkode ist schon 01!
|
||||
ldb rl7, #FORMAT
|
||||
read: outb @r4, rl7 !Kommando ausgeben!
|
||||
outb @r4, rl6 !Laufwerknummer!
|
||||
pop r1, @r15 !Cylinder!
|
||||
outb @r4, rl1 !Cylinder low!
|
||||
outb @r4, rh1 !Cylinder high!
|
||||
pop r1, @r15 !Kopf!
|
||||
outb @r4, rl1
|
||||
outb @r4, rl3 !Sektor!
|
||||
ld r3, #%200 !Laenge!
|
||||
outb @r4, rl3
|
||||
outb @r4, rh3
|
||||
outb @r4, rh6 !Pruefsumme, nicht benutzt!
|
||||
|
||||
wwait0: inb rl0, @r5 !Warten bis WDC Status 0!
|
||||
bitb rl0, #0
|
||||
jr z,wwait0
|
||||
|
||||
rwwait: inb rl1, @r5 !Status einlesen!
|
||||
bitb rl1, #0
|
||||
jr nz, rwwait !auf Beendigung des Kommandos warten!
|
||||
inb rl1, @r5
|
||||
andb rl1, #%07 !Maske!
|
||||
ldk r2, #0 !Returncode kein Fehler!
|
||||
cpb rl1, #%06 !Status 1 = fertig, kein Fehler!
|
||||
ret z
|
||||
|
||||
ld r0, #RDATA+INPUT
|
||||
outb PIOAC, rl0 !Daten-PIO auf Eingabe!
|
||||
outb @r5, rh0 !Treiber auf Eingabe!
|
||||
inb rl0, @r4 !Scheineingabe!
|
||||
cpb rl1, #%04 !Status 3 Daten einlesen ?!
|
||||
jr nz, error !nein, Fehler!
|
||||
|
||||
lda r6, rbuffer
|
||||
inirb @r6, @r4, r3
|
||||
ret
|
||||
|
||||
error: inb rl2, @r4 !Fehlercode einlesen!
|
||||
ret
|
||||
end _fdisk
|
||||
|
||||
|
||||
!Initialisierung der Ports und des Controlers!
|
||||
|
||||
internal
|
||||
|
||||
init array [* byte] := [
|
||||
PIOBC, INTVEC !Int Vektor holt PIO Port aus Reset!
|
||||
PIOBD, WDATA !Reset wegnehmen, Richtung auf Write!
|
||||
PIOBC, BITMODE !Port B auf Bitmode programmieren!
|
||||
PIOBC, %87 !bit 7,2,1,0 auf Eingabe!
|
||||
]
|
||||
|
||||
_disk_in procedure
|
||||
entry
|
||||
ld r2, #PIOBD
|
||||
inb rl1, @r2 !PIOBD schon initialisiert ?!
|
||||
bitb rl1, #5
|
||||
ret z !ja!
|
||||
|
||||
lda r1, init
|
||||
ldk r0, #(sizeof init)/2 !Anzahl der Ausgaben!
|
||||
iloop: ldb rl2, @r1 !low Portadresse!
|
||||
inc r1, #1
|
||||
outib @r2, @r1, r0
|
||||
jr nov, iloop
|
||||
ret
|
||||
end _disk_in
|
||||
end fdisk
|
||||
|
|
@ -1,104 +0,0 @@
|
|||
/**************************************************************************
|
||||
**************************************************************************
|
||||
|
||||
W E G A - Quelle (C) ZFT/KEAW Abt. Basissoftware - 1985
|
||||
Standalone: sa.format.c
|
||||
|
||||
|
||||
Bearbeiter : P. Hoge
|
||||
Datum : 04/01/87 11:15:41
|
||||
Version : 1.1
|
||||
|
||||
**************************************************************************
|
||||
**************************************************************************/
|
||||
|
||||
#define NSECTS 18
|
||||
|
||||
char buf[10];
|
||||
unsigned int drive;
|
||||
unsigned int nsect;
|
||||
unsigned int fhead;
|
||||
unsigned int lhead;
|
||||
unsigned int fcyl;
|
||||
unsigned int lcyl;
|
||||
|
||||
main()
|
||||
{
|
||||
register cyl;
|
||||
register head;
|
||||
register error;
|
||||
register sect;
|
||||
|
||||
printf("\nFormat Winchester-Drive\n");
|
||||
do {
|
||||
printf("Drive: ");
|
||||
drive = input();
|
||||
}while(drive > 1);
|
||||
|
||||
do {
|
||||
printf("First Head: ");
|
||||
fhead = input();
|
||||
}while(fhead > 8);
|
||||
|
||||
do {
|
||||
printf("Last Head: ");
|
||||
lhead = input();
|
||||
}while(lhead > 8 || fhead > lhead);
|
||||
|
||||
nsect = NSECTS;
|
||||
|
||||
do {
|
||||
printf("First Cylinder: ");
|
||||
fcyl = input();
|
||||
}while(fcyl > 1023);
|
||||
|
||||
do {
|
||||
printf("Last Cylinder: ");
|
||||
lcyl = input();
|
||||
}while(lcyl > 1023 || fcyl > lcyl);
|
||||
|
||||
printf("Format: drive %d, %d sectors/track, cylinder %d - %d, head %d - %d\n", drive, nsect, fcyl, lcyl, fhead, lhead);
|
||||
printf("Ready to Format ?: ");
|
||||
inyes();
|
||||
for (cyl=fcyl; cyl<=lcyl; cyl++) {
|
||||
for (head=fhead; head <= lhead; head++) {
|
||||
printf("Format - cylinder: %d head: %d\r", cyl, head);
|
||||
error = fdisk(3, drive, head, nsect, 1, cyl);
|
||||
if ( error != 0) {
|
||||
printf("\nError 0x%x - continue ?: ", error);
|
||||
inyes();
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
for (cyl=fcyl; cyl<=lcyl; cyl++) {
|
||||
for (head=fhead; head <= lhead; head++) {
|
||||
printf("Verify - cylinder: %d head: %d \r", cyl, head);
|
||||
for(sect = 1; sect <= nsect; sect++) {
|
||||
error = fdisk(1, drive, head, nsect, sect, cyl);
|
||||
if (error != 0) {
|
||||
printf("\nError 0x%x on sector %d - continue ?: ", error, sect);
|
||||
inyes();
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
printf("\n");
|
||||
exit();
|
||||
}
|
||||
|
||||
input()
|
||||
{
|
||||
gets(buf, 10);
|
||||
if (buf[0] < '0' || buf[0] > '9')
|
||||
exit();
|
||||
return(atoi(buf));
|
||||
}
|
||||
|
||||
inyes()
|
||||
{
|
||||
gets(buf, 3);
|
||||
if (buf[0] == 'y' || buf[0] == 'Y')
|
||||
return;
|
||||
exit();
|
||||
}
|
||||
|
|
@ -1,93 +0,0 @@
|
|||
/**************************************************************************
|
||||
**************************************************************************
|
||||
|
||||
W E G A - Quelle (C) ZFT/KEAW Abt. Basissoftware - 1985
|
||||
Standalone: sa.verify.c
|
||||
|
||||
|
||||
Bearbeiter : P. Hoge
|
||||
Datum : 04/01/87 11:16:15
|
||||
Version : 1.1
|
||||
|
||||
**************************************************************************
|
||||
**************************************************************************/
|
||||
|
||||
#define NSECTS 18
|
||||
|
||||
char buf[10];
|
||||
unsigned int drive;
|
||||
unsigned int nsect;
|
||||
unsigned int fhead;
|
||||
unsigned int lhead;
|
||||
unsigned int fcyl;
|
||||
unsigned int lcyl;
|
||||
|
||||
main()
|
||||
{
|
||||
register cyl;
|
||||
register head;
|
||||
register error;
|
||||
register sect;
|
||||
|
||||
printf("\nVerify Winchester-Drive\n");
|
||||
do {
|
||||
printf("Drive: ");
|
||||
drive = input();
|
||||
}while(drive > 1);
|
||||
|
||||
do {
|
||||
printf("First Head: ");
|
||||
fhead = input();
|
||||
}while(fhead > 8);
|
||||
|
||||
do {
|
||||
printf("Last Head: ");
|
||||
lhead = input();
|
||||
}while(lhead > 8 || fhead > lhead);
|
||||
|
||||
nsect = NSECTS;
|
||||
|
||||
do {
|
||||
printf("First Cylinder: ");
|
||||
fcyl = input();
|
||||
}while(fcyl > 1023);
|
||||
|
||||
do {
|
||||
printf("Last Cylinder: ");
|
||||
lcyl = input();
|
||||
}while(lcyl > 1023 || fcyl > lcyl);
|
||||
|
||||
printf("Verify: drive %d, %d sectors/track, cylinder %d - %d, head %d - %d\n", drive, nsect, fcyl, lcyl, fhead, lhead);
|
||||
printf("Ready to Verify ?: ");
|
||||
inyes();
|
||||
for (cyl=fcyl; cyl<=lcyl; cyl++) {
|
||||
for (head=fhead; head <= lhead; head++) {
|
||||
printf("Verify - cylinder: %d head: %d \r", cyl, head);
|
||||
for(sect = 1; sect <= nsect; sect++) {
|
||||
error = fdisk(1, drive, head, nsect, sect, cyl);
|
||||
if (error != 0) {
|
||||
printf("\nError 0x%x on sector %d - continue ?: ", error, sect);
|
||||
inyes();
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
printf("\n");
|
||||
exit();
|
||||
}
|
||||
|
||||
input()
|
||||
{
|
||||
gets(buf, 10);
|
||||
if (buf[0] < '0' || buf[0] > '9')
|
||||
exit();
|
||||
return(atoi(buf));
|
||||
}
|
||||
|
||||
inyes()
|
||||
{
|
||||
gets(buf, 3);
|
||||
if (buf[0] == 'y' || buf[0] == 'Y')
|
||||
return;
|
||||
exit();
|
||||
}
|
||||
Loading…
Reference in New Issue